Tag Archives: eeprom programmer

How to install WinOLS 2.24 on Windows 7/XP 32bit

new-genius-flash-point-obdii-tuning-tool-2-620x264

FREE WinOLS v2.24 Where to get:

http://www.eobdtool.fr/wholesale/genius-flash-point-ecu-chip-tuning-tool.html

https://mega.nz/#!AApGDKpL!MV84PFdQIiNFwXdggnSC5yhGe-3edK92weYv0X0tQNA (not tested)

WinOLS 2.24 software is not sold separately on the web. If you want tested WinOLS software only, go to WinOLS v1.500:

http://www.eobdtool.fr/wholesale/winols-version-1500-with-unlock-patch.html (€9)

For WinOLS tested versions:

Only working under 32 bit systems (Windows XP or 7)

How to install WinOLS 2.24 Windows 32 bit:

First, it’s a customer solution. Good luck.

I ended up getting it installed.

1. Install “setup.exe”

2. Take the following 3 files:
EVC_key.dll
EVClicenceMOD.dll
loader_ols_32bit

and put them here:
C:\Program Files\EVC
***THIS IS WHERE MINE WAS GOING WRONG, SETUP.EXE AUTOMATICALLY INSTALLS THE EVC FOLDER INTO “PROGRAM FILES (X86)” IF THIS IS THE CASE, MOVE THE WHOLE “EVC” FOLDER INTO THE NORMAL PROGRAM FILES, NOT PROGRAM FILES X86***

3. Install “winols_testversion.exe” and run through the setup, just keep clicking yes/OK. At the end of the install it will launch the program, let it do that, but just close it after it opens, don’t play around with it.

4. Go back into C:\Program Files\EVC and double click “loader_ols_32bit”, this should bring up a window saying something along the lines of “Restart the app”. If it says “error starting app”, you’ve gone wrong somewhere. Take note of the red bit above ^

5. Go to start>control panel>add/remove a program>uninstall WinOls 2.14.03
This is the test version you just installed, DON’T delete the full version you installed first.

6. Again, go back into C:\Program Files\EVC and right click “loader_ols_32bit” and send to desktop. This will create a shortcut on the desk top. Then, on the desktop, delete the shortcut to WinOls. If you open WinOls directly it will mess it all up, you have to open the program by using “loader_ols_32bit” which now also has a shortcut on the desktop. I renamed the loader shorcut “WinOls” to simplify things.

Lastly, tune things, give them massive amounts of power, give horsepower to the people, fry tyres and make lots of noise.

First install WinOLS_Testversion.exe & launch program, configure as required

Once the application is opened close it & uninstall via “Add or Remove Programs” via control panel or “Programs & Features” (W7)

Navigate to C:\Program Files

Now copy / paste the “EVC” folder to this location. If you get a question about folder replacement answer “YES TO ALL”

Now navigate to C:\Program Files\EVC

Right click on “loader_ols_32_XP_free.exe” then select send shortcut to desktop (You can rename it later)

Now run the program using the shortcut & you will get a message about the License key completed, click OK

Now run again the program & configure as required ….You should now have a registered version of WinOLS 2.24

Genius and Flash Point ECU Chip Tuning Tool TF Card Reset Procedure

Genius and Flash Point ECU Chip Tuning Tool TF Card Reset Procedure

Sometimes, you may find that the file side the Genius and Flash Point ECU Chip Tuning Tool TF Card ruined. Then you will need to fix the file of the TF card. This video is to fix the TF card file for the Genius & Flash K-touch ECU Tool.

Tips1: You only can use the TF card from a complete set of the Genius. Do not use the TF card bought from the local market.
Tips2: Before fixing, you need to format the TF card.
Tips3: The k-touch.img fixing file must be in disk D or disk E. Do not put the k-touch.img in the file of the disk D or disk E.

MB Carsoft 7.4 Multiplexer Customer Shared FAQ

MB Carsoft 7.4 Multiplexer Customer Shared FAQ

Q1: Customer who brought the item SE25 only has the laptop with 15pin connector, but the device’s is 9pin. Can he use one convert USB cable for instead?
A1: No, he must use the laptop which can connect with our device directly.

Q2: MB Carsoft 7.4 Multiplexer, can it do motocycle?
A2: No, it can not

Q3: MB Carsoft 7.4 Multiplexer, does it has Spanish Language Version? Must I install it on Win XP System?
A3:: This MB Carsoft 7.4 Multiplexer only has English Language Version, and it can only be used on Win XP System

Q4: What can I do by this?
A4: You can read/erase all fault codes

Q5: Which year of car it is mainly available on?
A5: It mainly for the car from 1996 to 2005.

Our customer have such question that when install mb carsoft 7.4, it asks activation code, does it need or not? please firstly check the questions and the related error message in details.

Q: When I use the MB carsoft 7.4 multiplexer, it ask the activation code. Does it need activation?

mb-carsoft-1

mb-carsoft-2

mb-carsoft-3


A: This is the problem of operating system or the wrong installation steps. It deos not need to be activated. We do suggest clients use the professional xp system, please check the file or the manual of how to setup MB carsoft 7.4.

Xprog Programmer Differences Listed on EOBDTOOL.FR

Xprog Programmer Differences Listed on EOBDTOOL.FR

As we all known, the XPROG programmer is fully upward-compatible hardware with XPROG programmer and have many additional features. And there are many diffent versions of the Xprog or the Xprog-M online. Which one to choose? What are the differences?

Item Code SM48 SM48-B SM44-C SM11-D SM11-F SM11
Item Name XPROG-M V5.5.5 with USB Dongle +T420 Laptop +500GB HDD XPROG-M V5.5.5 with USB Dongle XPROG-M V5.50 without USB Dongle Xprog-m V5.3 with USB Dongle XPROG-M V5.3 Main Unit XPROG-M V5.0without USB Dongle
Version V5.5.5 V5.5.5 V5.5 V5.3 V5.3 V5.0
Language English
OS 32Bit/64Bit WinXP/Win7 System 32Bit WinXP EN System
with Dongle YES No YES No No
with Laptop YES (software installed) No No No No No
Update No No Yes (Check SO294-C) Yes (Check SO294-C) Yes (Check SO294-C) Yes (Check SO294-C)
Function Read/Write ECU/MCU Chip,Eeprom programming
Special Function Decypte New BMW CAS4;Add New Authorization: AUTH-0025 Authorized Decypte New BMW CAS4;Add New Authorization: AUTH-0025 Authorized supports more than 450 units (serial EEPROM’s, Microcontrollers (MCU), Electronics Control Units (ECU), DashBoards, Immobilizers, Calculators and others) support microchips freescale MAC, INFINEON, RENESAS supports microchips freescale MAC, INFINEON, RENESAS NO
Support List depends on ECU Chip Types
Xprog Serials products difference
1. Different Version
2. Except SM44-C,SM11-D,SM11 without dongle, replaced by Chips, Others contain dongle
3. No hardware version, different software version with different hardware version, except V5.0, v5.3 others is the same
4. V5.0 Xprog is much more stable than V5.3
5. you can buy SO294-C ATMEGA64 Repair Chip to  upgrade xprog before V5.5

Attention: Only Winxp 32bit System Supported. No Antivirus Progarm. No Internet Connection Before installing Software

KTAG K-TAG ECU Programming Tool Technique Support FAQ

KTAG K-TAG ECU Programming Tool Technique Support FAQ

Q1: Can I use KTAG on Windows XP?
A1: KTAG is compatible with both Windows XP and WIN7, but not all WIN7 is workable, better use WIN7 professional.

Q2: Ktag “Communication error: please check power and connections – ox1008.”

ktag-communication-error-01
A2: Please check whether the car ECU is connected with the power.

Q3: Does KTAG ECU programmer have limit number of times, only 32 and then throw it away?
A3: No, it has no limit you can always use it. But if you keep on giving ECU to write map file, then it has about 500 times limit. If your KTAG has limit counter and the KTAG board is no gluing, please contact us we will send you chip for replacement, but there are two conditions to change chip:
1) it is our KTAG not from other sellers;
2) you are required to know how to change the chip otherwise the KTAG will be damaged.

Q4: KTAG got error “checksum error”.

ktag-checksum-error-02
A4: there are three reasons cause checksum error:
1) the computer operation system is not compatible with KTAG, better use Windows XP or WIN7 professional;
2) there are some problem with KTAG software;
3) Ktag can’t work with these types of ECU at present. If needed, please ask us for remote assistance.

Q5: Do you have PDF instruction on this strip cable?

ktag-strip-cable
A5: Sorry, we only have KTAG driver installation video tutorial and BOOT cable instruction.
1)KTAG driver installation video tutorial: click column ” Video” at this page to watch or contact us to send you.
2)BOOT cable instruction as the following shows:

ktag-boot-cable-instruction

How to solve V2.11 KTAG K-TAG Master ECU Programming Tool Version 0?

How to solve V2.11 KTAG K-TAG Master ECU Programming Tool Version 0?

V2.11 KTAG K-TAG ECU Programming Tool Master with Hardware V6.070 is latest V2.11. It supports BDM function well and has no tokens limitation.  Available Protocols for K-TAG: BDM MOTOROLA MPC5xx.

Customer Question: I used the KTAG K-TAG Master ECU Programming Tool for 3 weeks. But yesterday when I connected the ktag interface with my car, it prompted the Version FW:0. How can I do?

ktag-error

Answer: Please try to press the Ktag renew button. After pressing, connect the power supply cable. The light will turn to red. Then follow the unlock video in the software CD.

ktag-renew-button

KESS V2 OBD2 Manager Tuning Kit Installation and Usage Customer Feedback

KESS V2 OBD2 Manager Tuning Kit Installation and Usage Customer Feedback

Q1: Where to download KESS V2 driver?
A1:You can contact our customer service for the download link.

Q2: When KESS V2 read ECU, I got checksum error.
A2: Please search “visual C++ 2005 library” on Google, then download it and install it, this error will be solved.

Q3(1): How does KESS V2 checksums work? Does KESS V2 automatically confirm and rewrite? Does KESS v2 work with truck? Such as: Mercedes MP1/MP2/MP3 or MAN TGA.
A3(1): After reading the software, kess v2 will automatically calibrate checksums. KESS V2 doesn’t work with truck, because the truck voltage is too high and KESS V2 will be burnt out.
Q3(2): Then K-tag work with truck?
A3(2): Yes, it does.

Q4: How to connect KESS V2 to K-LINE med 17, do you have any manual or diagram?
A4: If your car is OBD diagnostic socket, just plug the OBD cable into the car; if your car is not OBD diagnostic socket, after you select the CU type in the KESS V2 software, the diagram will appear and show you how to connect (see the following pictures)

kess-v2-select-ecu-01 kess-v2-select-ecu-02 kess-v2-select-ecu-03 kess-v2-select-ecu-04

kess-v2-select-ecu-05 kess-v2-select-ecu-06

How to distinguish different version of UPA Programmer on EOBDTOOL.FR?

How to distinguish different version of UPA Programmer on EOBDTOOL.FR?

Upa-usb is the full set with all adapters. The main Device can be directly connected to the Elrasoft.com UUSP (UPA-USB Serial Programmer). There are many different version of the Upa-usb online. How to choose the right one to use? Please see the form bellow:

upa-series-eobdtoolfr

1. The software version, main unit color, package adapters, function different.
2. Note: Ensure the UPA USB Programmer Software Driver is installed ok before Using.
UPA USB Programmer support NEC function, but do not include NEC adapter in the package. If you want to use this function, you need to buy the NEC adapter(SM03) by yourself.

EOBDTOOL.FR Fgtech Galletto Series Comparision

EOBDTOOL.FR Fgtech Galletto Series Comparision

FG Tech Galletto 4-Master V54 BDM-TriCore-OBD is a famous chip tuning tool for all cars, trucks, motorcycles, Marine, BDM MPCxx, BDM Boot Mode,checksum. V54 FGTech can not only work as FGTech Galletto 4-Master, but also work for BDM-TriCore-OBD. There are many fgtech ecu master online. Now we will distinguish the differences between those devices.

fgtech-eobdtoolfr

Fgtech Series List:

FGTech Galletto 2-Master EOBD2
2012 New FGTech Galletto 2-Master V5.0 with BDM adaptor
2014 V54 FGTech Galletto 4 Master BDM-TriCore-OBD Function
V54 FGTech Galletto 4 Master BDM-TriCore-OBD Function